Table of Contents
Spaenaur Catalog 14 - Digital Flipping Catalog
CATALOG 14 M P : 1-800-265-8772 F : 1-888-252-6380 www. .com Inch Pouce Standardized Brass Eyelets & Fastener Tools M32 19 JAN 2018 E-22 E-23 E-24 E-25 E-26 E-27 E-63 E-64 E-65 E-66 E-67 E-68 E-69 E-611 E-610 E-612 E-613 E-33 E-34 E-39 E-36 E-37 E-39 E-310 E-311 E-38 HOW TO SELECT E EYELETS EYELET HAND PRESS APPLICATION OF EYELETS REQUIRES HAND PRESS, DIES (MALE & FEMALE) AND POSSIBLE ARBOR ADAPTOR Sold in Complete Sets Only. (Male and Female Dies) DIES WITH 5/16" ARBORS. Die Set No. For Eyelet Dia. T-234-2 2/32" (.059") T-234-3 3/32" (.089") T-234-4 4/32" (.121") T-234-5 5/32" (.152") T-234-7 7/32" (.215") T-234-8 8/32" (.246") DIES WITH 5/16" ARBORS, AND 3/8" ADAPTERS. T-211 2/32" (.059") T-212 3/32" (.089") T-213 4/32" (.121") T-214 5/32" (.152") T-215 6/32" (.183") T-216 7/32" (.215") T-217 8/32" (.246") EYELETTING DIES FOR BRASS EYELETS T-194A-M (Male) Converts 5/16" to 3/8" T-194A-F (Female) Converts 5/16" to 3/8" Die sets T-211 to T-217 may be used with 876-830 Hand Press. Accepts Dies having 3/8" Shank Dia. Complete Hand Press information on page M26 . ARBOR ADAPTERS PKG QTY. 1 (Dies not included.) SPAENAUR No. 876-830 PKG QTY. 1 Die Set No. For Eyelet Dia. 1 2 3 Arbor adaptor required for 5/16” eyelet diameter A. DETERMINE GRIP Eyelet grip is the thickness which can be held between the flange and the setting and will vary with the materials being eyeleted. Maximum grips listed in the chart are based on test settings made in metal panels and are intended only as a guide for your use. It is recommended that sample settings be made for each new application. To determine the grip, measure the total thickness of the materials to be eyeleted. Locate the corresponding grip in the chart. Reading to the right will identify the various standard E Eyelets which will provide the desired grip. Example: Assume the material(s) to be eyeleted have a total work thickness of .175". Reading vertically down the DESIRED GRIP column locate the nearest standard grip figure which is .176". Now reading horizontally to the right, identify the various E Eyelets which will provide the required grip, that is E27, E38, E48, E58, E68, E78 and E88. B. DETERMINE EYELET SIZE With a possible selection of three or more eyelet sizes available for a given grip, the function of the eyelet will help determine the eyelet diameter to be used. Will the eyelet be subjected to tensile or shear stresses, is the size of the hole to receive the eyelet already established, is the inside diameter critical because something will be passed through the eyelet, or will the eyelet be used as a decoration and size becomes an aesthetic decision? C. DETERMINE WORKING DIMENSIONS Eyelet dimensions and required hole sizes are all identified for your convenience. DESIRED GRIP .020 .035 .040 .045 .051 .067 .072 .077 .082 .098 .103 .108 .113 .129 .134 .139 .144 .161 .166 .171 .176 .192 .197 .202 .203 .233 .254 .264 .228 .259 .286 .290 .291 .317 .348 .353 .322 .328 E-43 E-44 E-46 E-47 E-48 E-410 E-411 E-412 E-45 E-49 E-53 E-54 E-55 E-56 E-58 E-59 E-570 E-511 E-57 E-73 E-74 E-75 E-76 E-77 E-78 E-710 E-711 E-712 E-79 E-83 E-84 E-85 E-86 E-87 E-88 E-810 E-89 E-811 E-812 E-813 E EYELET SIZES Œillets en laiton standardisés et outils de fixation F : 1- 8-252-6380 service@spaenaur © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.