Spaenaur Catalog 14 - Digital Flipping Catalog

CATALOG 14 D P : 1-800-265-8772 F : 1-888-252-6380 www. .com Nord-Lock Data Sheet D35 D Bolt 3/16" 1/4" 5/16" 3/8" 7/16" 1/2" 9/16" 5/8" 3/4" 7/8" 1" 1-1/8" 1-1/4" 1-3/8" 1-1/2" Size (M5) (M6) (M8) (M10) (M11) (M12) (M14) (M16) (M20) (M22) (M24) (M30) (M33) (M36) (M39) Grade 2* N/A 8 16 28 44 66 96 131 231 225 338 481 675 875 1144 Grade 5* N/A 11 24 41 67 101 144 200 362 581 875 1075 1513 1963 2587 Grade 8* N/A 16 34 59 95 144 206 287 506 825 1225 1738 1831 3187 4200 Nord-LockWashers maintain preload at loosening movements. Due to the preload, the screw is prevented from turning in either direction. Should the screw tend to loosen, it causes the mating washer to slide up the cams on the other washer, producing a wedge action, and the preload is maintained. These washers can be used on low-grade and high-grade screws, and on joint surfaces with hardness up to HRc45. INTERLOCKING CAMS CAUTION The superior locking performance of a Nord-Lock fas- tener is secured only if it is correctly assembled and the proper Nord-Lock fastener combination is selected. It is imperative that the following instructions are closely observed: Nord-Lock Washer Pairs must be assembled cam face to cam face. When used in conjunctionwith a bolt/nut fastener, install a pair of Nord-Lock Washers, cam face to cam face, between both the bolt head and the joint material and the nut and the joint material (see Fig. 1). The teeth of the washer pairs will now bite into the bolt head and the joint material as well as the nut, and the joint material on the corresponding side. When used in conjunction with a cap screw or bolt in a threaded hole, install one pair of Nord-Lock Washers, cam face to cam face, under the cap screw or bolt head (see Fig. 2). The teeth of thewasher pair will nowbite into the cap screw or bolt head on one side and the joint material on the other side. READ BEFORE INSTALLING NORD-LOCK WASHER PAIRS FIG. 1 FIG. 2 Assemblies Nord-Lock washers can be used on standard as well as high-grade bolts. When tightening, a 20% higher torque is used than on standard flat electro-zinc plated washers. When tightening the fastener to preload, the teethpenetrateand seat against the joint material and the nut and/or fastener head. When subjected to vibration the interacting cams create a wedge action thereby maintaining preload in the joint which prevents the fasteners from vibrating loose. The Nord-Lock Principle The Nord-Lock washer has cams or wedges on one side, with a lead angle greater than a thread angle, and radial teeth or ribs on the other side. The washers are installed cam face to cam face, forming the unique Nord-Lock fastener. Hold the screw cap when tightening the nut. BENEFITS OF NORD-LOCK The key is the difference in angles. Here you see what happens when a nut attempts to loosen. The pair of washers expand more than the corresponding pitch of the thread. Nord-Lock washers positively lock the fastener in a joint which is subjected to extreme vibration. *Recommended torque - ft./lbs. See following pages for Nord-Lock ® Washers. 16 Jan 2018 Technical Information provided by Nord-Lock. For critical applications testing in the actual assembly should be conducted to determine Torque Values. Fiche de données Nord-Lock F : 1- 8-252-6380 service@spaenaur. © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.

RkJQdWJsaXNoZXIy MzMyMjI=