Spaenaur Catalog 14 - Digital Flipping Catalog

CATALOG 14 C P : 1-800-265-8772 F : 1-888-252-6380 www. .com Inch and Metric Pouce et Métrique On-Serts / Applicator Tools C197 23 Jan 2018 ON-SERT FASTENERS PLASTIC BOSS SPAENAUR Min. Dia. No. (see Note 1) Height Dia. Weight I.D. of Ctsk. Applicator Thread Inch SPAENAUR H D Lbs./M O.D. (In.) C Tool Size Thread Metric Size No. Design (In.) (In.) Pieces (In.) (see Note 2) (In.) (see Note 3) 4-40 628-001 1 .220 .284 1.0 .247-.253 .096-.100 .180 876-278 6-20 & 6-18 628-003 1 .230 .354 1.5 .116-.120 .250 876-280 8-18 & 8-15 628-005 1 .230 .354 1.4 .140-.144 .290 876-281 8-18 & 8-15 628-B78-1T 1 .230 .328 1.3 .279-.285 .140-.144 .220 876-280 8-18 & 8-15 628-007 1 .260 .544 3.5 .497-.503 .140-.144 .290 876-284 8-18 & 8-15 628-008 1 .254 .556 3.0 .509-.515 .140-.144 .290 876-285 628-009 1 .220 .422 1.9 .140-.144 .290 876-282 628-010 2 .280 .422 1.9 .185-.250 none 876-286 628-011 1 .220 .422 1.9 .140-.144 .290 876-283 10-12 & 10-16 628-013 1 .230 .422 1.8 .160-.164 .290 876-282 Design 1 Screw enters through top of boss Design 2 Screw enters through bottom of boss NOTE 1. The thread form of Parts 628-001 and 628-011 is designed to accept either a machine screw or Type F Tapping Screw of the thread size designated. Each of the other parts accommodates a Tapping Screw of the size indicated. NOTE 2. For maximum screw pull-out resistance with Design 1 parts, the boss I.D. should be as specified above to provide an interference fit with the screw. On-sert fasteners can also be used where the screw clears the I.D. of the boss, but this arrangement reduc es resistance to screw pull-out. NOTE 3. Design 2 parts should always be installed with the appropriate applicator tool which is designed to protect the projecting thread form from deformation by pressure or a direct blow. Although Design 1 parts may be installed by tapping directly on the top of the fasteners with a hammer, the magnetized applicator tool facilitates handling and positioning. These distinctive fasteners, with a single helical thread, slip over hollow plastic bosses and prevent splitting when screws are driven. They also prevent cross-threading, and resist screw pull-out, yet screws may be removed without harming the fasteners or the boss. On- sert fasteners thus perform the same function as solid inserts, but cost only about one-fifth as much. One type is used when screws enter the top of a boss, while another type is used when screws enter the bottom of the boss. On-Serts ® They fit “ON THE BOSS” (With protective finish) STEEL .372-.378 8-18 & 8-15 .309-.315 8-32 On-Sert ® APPLICATOR TOOLS Style 2 Overall Bolt SPAENAUR No. Style Length Clearance Dia. Fastener Tool No. L Depth D 628-001 876-278 2 3" 1/2" 628-003 876-280 2 3" 1/2" 628-005 876-281 4 3" 1/2" 628-B78-1T 876-280 2 3" 1/2" 628-007 876-284 2 3" 3/4" 628-008 876-285 4 3" 3/4" 628-009 876-282 2 3" 5/8" 628-010 876-286 3 1-13/16" 1-1/4" .615" 628-011 876-283 4 3" N/A 5/8" 628-013 876-282 2 3" N/A 5/8" Not applicable Style 4 Style 3 INCH SIZES 3.5mm 3.5mm 4.2mm 4.2mm 4.2mm 4.2mm 4.2mm 4.2mm 4.8mm PKG QTY. 100 - ALL ON-SERTS Tools PKG QTY. 1 On-sert Douilles On-Serts / Outils d'applicateur d'insert fileté F : 1- 8-252-6380 service@spaenaur. © 2018 Spaenaur Inc. All rights reserved. Catalog may not be reproduced, in whole or in part, without the written permission of Spaenaur Inc. Subject to Catalog Terms and Conditions of Use available at Spaenaur.com and on page TC2 and TC3 at the back of this catalog. © 2018 Spaenaur Inc. Tous droits réservés. Le catalogue ne peut être reproduit, en tout ou en partie, sans l’autorisation écrite de Spaenaur Inc. L’utilisation est soumise aux Conditions d’utilisation du Catalogue disponibles sur Spaenaur.com et à la page TC4 et TC5 à la fin de ce catalogue.

RkJQdWJsaXNoZXIy MzMyMjI=